In fact, most of the technical parameters of LED display screens are not understood. LED screens are composed of countless LED light-emitting diodes. Although LED light-emitting diodes belong to monochromatic light, LEDs of various colors still have a half-wave width of about 30-50nm. Therefore, the color saturation is limited, so this time we will get to know the color processing technology of LED display screen. Although it may not be understood, a simple understanding is not harmful.
1. 3 plus 2 multi-primary color processing method:
In recent years, in the field of flat panel displays, there has been a keen discussion of 3 plus 3 multi-primary color displays (red, green, blue plus yellow, cyan, and purple) to expand the color gamut and reproduce richer natural colors. So, can the LED display achieve 3 plus 3 multi-primary color display? Below, Winbond will discuss with you.
Indoor led display
We know that in the visible light range, yellow and cyan are monochromatic light, and we already have high-saturation yellow and cyan LEDs. While purple is polychromatic light, single-chip purple LEDs do not exist. Although we can not achieve red, green, blue plus yellow, cyan, purple 3 plus 3 multi-primary color LED display. However, it is feasible to study red, green, blue plus yellow, cyan 3 plus 2 multi-primary color LED display screens. Since there are a large number of high saturation yellow and cyan colors in nature; therefore, this research is of certain value.
In the current various television standards, the video source has only the three primary colors of red, green and blue, but not the two colors of yellow and cyan. So, how to drive the yellow and cyan two primary colors of the display terminal?
In fact, when determining the driving strength of the two primary colors of yellow and cyan, we follow the following three principles:
1. While increasing the color saturation, the hue must not be changed;
2. The purpose of increasing the two primary colors of yellow and cyan is to expand the color gamut, thereby increasing the color saturation. And the overall brightness value cannot be changed;
3. Take D65 as the center; take the RYGCB color gamut boundary as the end point, and linearly expand each point in the color gamut.
Under the guidance of the above three principles; according to the law of the center of gravity, we can find a 3 plus 2 multi-primary chromaticity processing method. However, if we want to truly realize a 3 plus 2 multi-primary full-color screen, we have to overcome difficulties such as insufficient brightness of the yellow and cyan LEDs and greater cost increase. At present, it is limited to theoretical discussions.
2. Color reduction processing:
With the birth of pure blue and pure green LEDs, full-color LED displays are sought after by the industry for their wide color gamut and high brightness. However, because the chromaticity coordinates of the red, green, and blue LEDs are quite different from the chromaticity coordinates of the red, green, and blue of the PAL TV (see Table 1), the color reproduction of the LED full-color screen is poor. Especially when expressing human skin color, there are obvious deviations in vision. As a result, the color reduction processing technology came into being. Here the author recommends two color reproduction methods:
1. Transform the color coordinate space of the red, green and blue LEDs to make the color coordinates of the three primary colors between the LED and the PAL TV as close as possible, thereby greatly improving the color reproduction of the LED display. However, this method greatly reduces the color gamut range of the LED display screen, and greatly reduces the color saturation of the screen.
2. Only the skin color gamut that is most sensitive to the human eye is properly corrected; and the color gamut that is not sensitive to other human eyes is as little as possible to reduce the original color saturation. In this way, a balance can be obtained between color reproduction and color saturation.
Three, the choice of primary color wavelength:
As people's requirements for led displays are getting higher and higher, only subdividing and filtering the color coordinates of LEDs can no longer satisfy people's discerning eyes. Comprehensive corrections are performed on the display to make the chromaticity uniform. The improvement is achievable.
We found that even the same grade of LED of the world's first brand has a large wavelength deviation and color saturation deviation, and the deviation range greatly exceeds the threshold value of the human eye for discrimination of green color difference. Therefore, it is important to perform color uniformity correction. meaningful.
In the CIE1931 chromaticity diagram, according to the law of the center of gravity, we found that at any point of the G range (□abcd) mixed with a certain proportion of red and blue, the color coordinates of the mixed color can be adjusted to the straight line cR and The intersection point O of the straight line dB.
Although the chromaticity uniformity can be greatly improved. However, the color saturation after correction is significantly reduced. At the same time, another prerequisite for the use of red and blue to correct the uniformity of green chromaticity is that the three LEDs of red, green and blue in the same pixel should be distributed as closely as possible to make the mixing distance of red, green and blue as close as possible to achieve better results. Effect. At present, the LED uniform distribution method is commonly used in the industry, which will bring confusion to the chromaticity uniformity correction. In addition, how to measure the color coordinates of tens of thousands of red, green and blue LEDs is also an extremely difficult problem. We have given a hint about this.
4. Chromaticity uniformity treatment:
The chromaticity uniformity of the led display has always been a major problem that plagues the industry. It is generally believed that the uneven brightness of the LED can be corrected by a single point to improve the brightness uniformity. The chromaticity unevenness cannot be corrected, and can only be improved by subdividing and filtering the LED color coordinates.
Five, the deployment of white field color coordinates:
White field color coordinate adjustment is one of the most basic technologies for full-color LED displays. However, in the mid-1990s, due to the lack of industry standards and basic testing methods, the white field color coordinates were usually determined by human eyes and sensations, resulting in serious color cast and randomness of white field color temperature. With the promulgation of industry standards and the completion of testing methods, many manufacturers have begun to standardize the color matching process for full-color screens. However, due to the lack of theoretical guidance for color matching, some manufacturers often sacrifice the gray levels of certain primary colors to adjust the 100-field color coordinates, and the overall performance cannot be improved.
Indoor led display
Then, based on the above, three aspects are mainly discussed about the chromaticity processing technology of the led display screen:
1. How to improve the chromaticity uniformity of the led display;
2. How to expand the color gamut and restore more natural colors;
3. How to improve the color reproduction of the led display;
The above-mentioned chromaticity processing technologies are all related to each other when they are implemented in practice, and some aspects are not even compatible with fish and bear's paws. The integrated LED display screen also needs to perform brightness uniformity correction, grayscale nonlinear transformation, noise reduction processing, image enhancement processing, dynamic pixel processing, etc., and the entire signal processing process is very complicated. Therefore, we must comprehensively weigh various performances from the perspective of the system, grasp the sequence of various processing, and increase the depth of signal processing, so that the LED full-color display can show a colorful, colorful and wonderful world.
Various industries have a very wide range of applications, and different applications have different requirements for the wavelength of the primary color of the LED. Some of the wavelengths of the primary color of the LED are selected to achieve good visual effects, some are to meet people's habits, and some It is also stipulated by industry standards, national standards and even international standards.
For example, the choice of the wavelength of the primary color of the green tube in a full-color LED display; in the early days, people generally used a yellow-green LED with a wavelength of 570nm. Although the cost is lower, the color gamut of the display is small, the color reproduction is poor, and the brightness is low. After choosing a pure green tube with a wavelength of 525nm, the color gamut of the display screen has nearly doubled, and the color reproduction has been greatly improved, which greatly improves the visual effect of the display screen. For another example, on the stock market display screen, people are usually accustomed to using red to indicate rising stock prices, green to indicate falling stock prices, and yellow to indicate flat prices. In the transportation industry, national standards strictly stipulate that the blue and green bands are traffic, and the red bands are forbidden. Therefore, the choice of primary color wavelength is one of the important links of led display screen.
"Conclusion" LED display chromaticity processing technology is actually just one of the many technical parameters of LED display. Although we may not be able to understand it, a preliminary understanding is still necessary, regardless of whether you are in the LED display industry or the customer There is always no harm in knowing more about product technology.
